天然橡胶混炼胶【哪里有卖】
橡胶止水带接头方法有两种：一种是采用粘接剂进行冷接头，一种是使用热硫化模具进行热接。 下边就分别介绍下两种接头方法：粘接剂冷接是采用橡胶止水带专用冷接胶水、采用搭接法把止水带需要接头的断面用磨光机磨平5~10厘米、涂胶水压实即可，具有强度高、凝固快的优点、施工方便、省时省力，可达到一般工程质量要求。 现场热接硫化法接头是使用与止水带匹配的热硫化模具及生胶片现场硫化热接，施工难度大，但接头效果理想，适合对工程质量要求严格的项目。1.可卸式止水带为我公司生产的橡胶止水带的一种，外观为中间半圆或者圆型两边平板结构，中间半圆结构是为了伸缩缝变形时有较好的拉伸及压缩，关键点在于两这的平板，不是浇注到混凝土中的，是混凝土施工完成后，经开槽安装膨胀螺栓及钢板安装在混凝土表面的。可卸式止水带可作为后期补救的一种防水措施，若伸缩缝漏水，可后期补入一层可卸止水带，这也就解释了为什么可卸，若出现可卸式止水带也被破坏，可将原来的卸掉，再重新安装一层。
There areo kinds of joint methods for rubber water belt: one is toe adhesive for cold joint, the other is toe hot vulcanization mould for hot connection. Below introduceso kinds of adhesive joint method: cold connection is thee of rubber sealing strip with special cold glue, overlapped by the water joints with grinder grinding section to 5~10 cm, glue can bepacted, has high strength, fast solidification has the advantages of convenient, time-saving, can meet the general engineering quality request. The field thermal contact vulcanization joint is a hot vulcanizing mold matched with the water belt and the on-site vulcanizing hot bonding of the raw film. The construction is difficult, but the joint effect is ideal, and it is suitable for the project with strict quality requirements. 1. detachable sealing strip for a rubber sealing strip produced by ourpany, look for
天然橡胶混炼胶【哪里有卖】
2.可卸式橡胶止水带安装固定：预埋螺栓须提前固定在钢板上,然后再浇筑预埋在混凝土中。应采用加钢板止水片的预埋钢板,预埋钢板下部的混凝土要仔细振捣。为便于安装可卸式止水带,变形缝的转角部位应做成圆弧形或45°角,圆弧半径应根据预埋螺栓的长度确定,以2个相邻螺栓头的距离不影响止水带和止水带夹板安装为准,一般以250 - 300 ε为宜。预埋钢板和夹板亦应做成相同形状。预埋螺栓时,应在螺栓上涂抹黄油后套短PVC管保护。2. the unloaded rubber sealing belt is fixed and fixed: the buried bolt t be fixed to the steel plate in advance and then put into the concrete. The pre buried steel plate with steel plate should beed, and the concrete under the buried steel plate should be carefully vibrated. To facilitate the installation of the detachable water, the corner part of the deformation joint should be circular or 45 degrees. The rad of the arc should be determined ording to the length of the embedded bolts. The distance been the 2 adjacent bolts does not affect the installation of the water and the watertight belt splint. Generally, the 250-300 e is suitable. Pre buried steel plates and splints should also be made in the same shape. When the bolt is buried, the bolt should be applied to the bolt to protect the bolt from the short PVC tube.
天然橡胶混炼胶【哪里有卖】
3.可卸式止水带的固定应在现场根据螺栓实际位置采用皮带冲打孔固定止水带,以保证其位置的准确性。在整个安装过程中,切不可使劲拉拽止水带。可卸式止水带与夹板间以及与预埋钢板间均应用石棉纸板或软金属片衬垫严密。3. the fixing of the unloaded water belt should be fixed on the spot bying a belt punching hole to fix the water belt in the actual position of the bolt, so as to ensure the uracy of its position. During the entire installation, the water belt t not be pulled hard. The hions of asbestos board or soft metal sheet are applied been the unloaded water belt and the splint and the pre buried steel plate.
1.遇水膨胀橡胶止水带除具有普通橡胶止水带的性能外，其主要特点是内防水线采用了具有遇水膨胀工程的特殊橡胶制成。这样在膨胀橡胶遇水膨胀后增强了止水带和构筑物的紧密度，使防水、止水效果更好。遇水膨胀橡胶止水带膨胀防水线部分胶料执行GB18173.3-2002标准。其余部分橡胶与普通橡胶止水带物理机械性能相同，执行GB18173.2-2000标准。
衡水汉江橡塑科技有限公司是橡胶止水带止水条、天然橡胶、防水涂料，防水卷材等产品专业生产加工的公司，。欢迎各界朋友莅临参观、指导和业务洽谈。欢迎致电：13091176335
